/ Register

An NSR Absolute Block instrument

Discussion in 'Miscellaneous & Oddities' started by Andy_Sollis, Aug 5, 2023.

Tags:
Page 16 of 19
  1. Jun 18, 2025 #301
    Mossy

    Mossy A classic grump Yorkshire man Full Member

    Messages:
    1,850
    Likes Received:
    2,795
    Joined:
    Sep 8, 2020
    Missed a question, whats the height of the lettering in inches, I can easily convert those into points.
     
  2. Jun 18, 2025 #302
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    On day shift so not home till aft 5.
    May need all three. Thought I’d try and clean the panels, the white one was original paint work (as is the green) with the outer being newer paint (hence the shade difference) and I’ve smudged the black letters with meths. and it didn’t clean anything else most disappointingly.
     
  3. Jun 18, 2025 #303
    Mossy

    Mossy A classic grump Yorkshire man Full Member

    Messages:
    1,850
    Likes Received:
    2,795
    Joined:
    Sep 8, 2020
    I planed doing 2 copies of all 3, it will be the same cost as a single print as most companies print sheets of transfers on either A4 or A5
     
    Andy_Sollis likes this.
  4. Jun 18, 2025 #304
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    Last night I decided to bite the bullet.
    Mark out and slide some transfers in place.

    I’m pleased to say, it went quite well.
    IMG_2352.jpeg
    top row done. The card was used to align the tops of the letters. Although it looks like “line” is off at an angle, it’s an optical illusion and it’s actually straight.

    IMG_2354.jpeg And the lower panel.

    it’s still to be varnished and sealed in, so that’s probably Fridays job.

    To keep it safe it was fastened back in to the block.
    IMG_2355.jpeg

    I think that’s looking good! Once it’s varnished, I will start adding the needles and aches on the front and the new needle stops. And the magnets on the rear.
     
    Jim Freight, Vinylelpea, Ron and 3 others like this.
  5. Jun 18, 2025 #305
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    @Mossy

    if you need any better let me know.

    IMG_2369.jpeg IMG_2375.jpeg IMG_2376.jpeg IMG_2373.jpeg IMG_2374.jpeg IMG_2370.jpeg IMG_2371.jpeg IMG_2372.jpeg IMG_2377.jpeg IMG_2379.jpeg
     
    York Paul and Ron like this.
  6. Jun 19, 2025 #306
    gormo

    gormo Staff Member Administrator

    Messages:
    6,730
    Likes Received:
    5,595
    Joined:
    Dec 5, 2015
    That looks great Andy.....most impressed.
     
    Andy_Sollis likes this.
  7. Jun 21, 2025 #307
    York Paul

    York Paul Staff Member Moderator

    Messages:
    6,277
    Likes Received:
    7,768
    Joined:
    Aug 20, 2017
    great work Andy... you just need a signal cabin in your garden now :avatar::tophat::tophat::tophat::tophat:
     
    Andy_Sollis likes this.
  8. Jun 21, 2025 #308
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    :scratchchin::scratchchin::scratchchin:

    Hmm. Now there is a thought. That would nicely p*ss the neighbour off! :avatar::avatar:
     
    York Paul likes this.
  9. Jun 21, 2025 #309
    York Paul

    York Paul Staff Member Moderator

    Messages:
    6,277
    Likes Received:
    7,768
    Joined:
    Aug 20, 2017
    Nothing like pronging your neighbour off...that's why I park an old single decker bus in the yard :avatar: ... we also do Morris dance practice in the garden on warm evenings and the cherry on the cake in late Autumn is a nice big smokey bonfire steaming away all the weeds. Just putting natural nutrient back into the land. :avatar:
     
    Andy_Sollis likes this.
  10. Jun 22, 2025 #310
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    The front panel has been rebuilt
    IMG_2409.jpeg
    starting with the inside. The spindle z mounts and the latches.

    IMG_2408.jpeg
    Finger pointers secured to the spindles and the front arch bearing mounts and the new felt bump stops
    IMG_2410.jpeg IMG_2411.jpeg
    and refitted
     
    Mossy, Jim Freight, York Paul and 2 others like this.
  11. Jun 22, 2025 #311
    Mossy

    Mossy A classic grump Yorkshire man Full Member

    Messages:
    1,850
    Likes Received:
    2,795
    Joined:
    Sep 8, 2020
    Andy,

    That looks stunning, congratulations mate. Now if you were an NER man you would get criticised because all the screw slots aren't lined up. Tee Hee :hismiley:

    Mossy
     
    Andy_Sollis likes this.
  12. Jun 23, 2025 #312
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    I've tried as I also like to do that. However, it would leave some parts loose. I have a screw still to shorten on one of the felt pads.

    I will try harder in future.. - the other art work has been test printed and will take home after work at 7am

    Andy
     
  13. Jun 23, 2025 #313
    gormo

    gormo Staff Member Administrator

    Messages:
    6,730
    Likes Received:
    5,595
    Joined:
    Dec 5, 2015
    Andy_Sollis and York Paul like this.
  14. Jun 23, 2025 #314
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    Final rub down started this aft (letting the meths dry)
    Then will start the polishing.
     
  15. Jun 23, 2025 #315
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    @Mossy
    We’re close. But not quite (I also think something is wrong with the colours, but not sure if my end or the printer at work! )
    IMG_2422.jpeg

    Im going to see if I can narrow the black lines and loose the outside one.

    IMG_2423.jpeg

    the text boxes also look small, but I may have to revert back to the original you sent and start again.

    IMG_2424.jpeg IMG_2425.jpeg
    keep you posted.
    Andy
     
    gormo likes this.
  16. Jun 23, 2025 #316
    Mossy

    Mossy A classic grump Yorkshire man Full Member

    Messages:
    1,850
    Likes Received:
    2,795
    Joined:
    Sep 8, 2020
    If your colours match those on the first transfers then it the printer at work, not your colouring. Can you check them out, but I have to say they look right from a distance.
    Leaving aside the actual colours, the 3 sets of literals shouldn't have a black box around them, and should be the same colour as the background. Probably my fault for leaving the drawn line around them, do you want a revamped Fusion file with then removed.

    Mossy
     
    Andy_Sollis likes this.
  17. Jun 23, 2025 #317
    Mossy

    Mossy A classic grump Yorkshire man Full Member

    Messages:
    1,850
    Likes Received:
    2,795
    Joined:
    Sep 8, 2020
    I missed the bit about the black lines. The 3 radial black lines are .5mm wide they can easily be reduced if needed as can the outer black circle. Let me modify the Fusion file and send you a new one.
     
    Andy_Sollis likes this.
  18. Jun 23, 2025 #318
    Jim Freight

    Jim Freight Full Member

    Messages:
    1,986
    Likes Received:
    1,711
    Joined:
    Sep 9, 2019
    Looks like the yellow is missing, an ink tank problem or similar :scratchchin:

    But why is the white odd?

    Jim :)
     
    Andy_Sollis likes this.
  19. Jun 24, 2025 #319
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    It’s a cream so probably as you say, missing yellow. A very good observation. ! (I had to use a different printer on another floor as ours wasn’t letting me sign in)
     
    Jim Freight likes this.
  20. Jun 24, 2025 #320
    Andy_Sollis

    Andy_Sollis Staff Member Moderator

    Messages:
    4,723
    Likes Received:
    4,777
    Joined:
    Aug 4, 2018
    The top has now had a wax polish (2 layers)

    IMG_2430.jpeg

    oh and I’ve added a name plate.
     
    Jim Freight, Vinylelpea and gormo like this.
Page 16 of 19

Share This Page