Sounds like toto has just slapped himself with a foisty kipper Not sure about stonemason, but may have been stoned Now just to lighten the stonework Window and roof to make, but I think that will wait until the building is planted, or at least the plot is dug out. Paul
Started digging the founds so to say - I seem to have a little subsidence, luckily I put a solid bottom on the building - the hole is where the polystyrene has been cleared for access to the bolt securing the boards. And the test fit Needs the ground building up down the side Paul
Looks fantastic once it's bedded into the surrounding scenics. It all looks very convincing. Well done that man. Now ...... We just need a roof ....... Get cracking. Toto
Back to the other board, and spun round to work on the rear bits. More flocking and rail side and my first attempt at water This section is on the rear, so is difficult for anyone to see - hence the test. The rear was dammed up with insulation tape backed with a lump of polystyrene held in place with Florists German pins. I've used neat Gloss Modge Podge for the water, then with a wet brush eased it into the sides, and a little at the start of the falls Just need to wait for it to dry to see if it worked. Paul
Keep coming back to look at this. ( even at 4 in the morning ) just trying to get my thick head around how these grasses and flocks were built up. It would be so easy to get it wrong and you only really get one attempt as once it's down........ it's down or at least really hard to recover. I'll be taking some more instruction. between the cover and the rock it's a fantastic result. Cheers Toto
Hi mate, the static grass is a doddle to apply. Put glue, I use neat pva, not too thick, but deep enough to hold the grass upright. Have you got an electrostatic applicator or a puffer bottle? If the former you will need to put an earth pin into the glue. As you are working in O scale now, the 2mm grass is ok if you are modelling a bowling green but it can be useful as a base layer for later taller applications. You will need some layering glue in an aerosol, I've used cheap unscented firm hold hairspray on mine. There are products out there that do the same job from such as Greenscene, WWscenics etc. You takes your pick etc etc. Spray the first layer then apply your 2nd layer of grass (I prefer to use longer strands, minimum 6mm, 10mm if I can get it) I also like to mix different colours of grass chucking in some dead grass colour (straw). Just repeat until you get the effect you like. Oh and don't forget to mask up where you don't want any grass as the spray WILL go everywhere. Also, if you want to have patches of longer or different shades of grass, cut an irregular hole the rough size of the patch in a piece of card and spray through that, then apply the grass. When you are finished after each layer and it has dried, use an old stocking or cut one leg off a pair of old tights, put the toe end into your vacuum cleaner, about three or four inches, hoover up the excess and tip it into a container to reuse. Hope this has been useful, just ask away if you need any help. Cheer's, Pete.
No worries, I've been watching a few online videos as well. I guess it's just a matter of planning ahead as to what you are trying to achieve before jumping in. Some folks can visualise these things better than others. It'll get there. Toto
Chris is brilliant at visualising things I am rubbish, having very little creative imagination. Give me something I can see and I can attempt to make it. Ask me to describe it if I haven't seen an example and you will get gibberish... Chris makes all the creative decisions in our house and I do the fetching an carrying
Well ..... Fetch Chris up here and she can do my scenics. I'm not so bad with the rock faces etc, it will be how to deal with the ground cover between the ballast. I'd like to do something a bit more varied than just grass to break things up a bit. It'll work out OK .... I'll come up with something. Cheers Toto
Toto I@ve just taken a few close ups of the track ends on Elton Crossing if that helps you, its the little details I think you may well find interesting... give us a few minutes and I'll upload onto the Elton Crossing Layout thread. I don't what to bomb on Dundee Paul's excellent work.
By the way Dundee Paul... I'm loving the build of this stone bothy... and can't wait to see the rest devenlop, the home made grass scenics look fab
Those rock faces look brilliant against the ground cover and ballasted track Paul ... it really does capture the feel of the terrain in Scotland... amazing stuff
Thanks guys, for the scenics its been created with three basic flocks All three are homemade The brown - is made from dried leaves, diced in the coffee grinder. The dark green is saw dust blended, then a mix of Daler Rowney Sap Green and Raw Umber acrylic added to the blender. The lighter green is sieved saw dust ( passed through an old spatter gaurd), again blended in the coffee grinder and Sap green and raw umber added (not as much as the darker green). I paint cheap PVA on to the surface, sprinkle a very small amount the brown then the greens. Finally using a pippette cover the lot in IPA (not beer variety - thats saved for later). Paul
Thanks Dundee Paul for your scenic recipe... I'm glad to hear you are not using English beer as a basing glue... now just as a thought would tea leaves work as a ground cover and if so would they need to be sterilized to stop little crawly things hatching out everywhere.
Actually, if you want to make a bright green ares after its rained, try mixing used dried out coffee grinds in with a a bright green flock, you'll be surprised at the result. For the tea leaves nuke em in a microwave